Density based traffic signal system using image processing

Contact Me for Project Prize Mail Id:  tamilblogelectronic@gmail.com Measure Traffic density and ambulance detection in Realtime project. What We Do in This Project: (Both Software & Hardware Project Available) ( i) Traffic Density Measure - Realtime (Means using Traffic Camera or Traffic Video) First,  we do Vehicle Detection in Video/Camera using Image Processing. Second, we Count the Vehicle We Detected in Video/Camera using Image Processing. Third, We Compare Two lane Vehicle Density in Video/Camera , if lane detect more no. of vehicle will be Prioritized first.   (ii) Ambulance Detection in Single Lane  - Realtime (Means using Traffic Camera or Traffic Video) : First, We Collect the Images of Ambulance. Second, we train our Image model using sample ambulance image. using Yolo image Model, we able to Detect the Ambulance in Video/ Camera. (iii) Ambulance Detection in Multiple Lane  - Realtime (Means using Traffic Camera or Traffic Vid...
Post a Comment

what is power amplifier in electronics?

(Note: Click Label To Check various Topics like Diodes,Rectifier,etc.)

Contact tamilblogelectronic@gmail.com And other social media for Soft copies of any Book.

What is  Power Amplifier ?

A power amplifier is the last stage of multistage amplifier system.  The input signal level to the power amplifier stage is of the order of a few volts as compared to small signal amplifiers where input signal is in microvolts or millivolts

The Basic Structure Of A Power Amplifier With A Block Diagram.

We Use The Example Of A Public Address System Amplifiers.  
The System Consists Of Many Stages Connected In Cascade. 
It Is Basically A Multistage Amplifier. 

The Input Is The Voice Band Sound Signals While Output Is The Amplified Signal Fed To A Loudspeaker.     

STRUCTURE OF A POWER AMPLIFIER by TAMIL BLOG Electronics
STRUCTURE OF A POWER AMPLIFIER



The Input First Stage And Intermediate Stages Are  Small Signal Amplifiers. Sufficient Voltage Gain Is Obtained In The Intermediate Stages. Hence These Stages Are Called Voltage Amplifiers.

The Last Stage Is Called A Power Amplifier Stage. 

The Output Of The Power Amplifier Is Fed To A Load (Loudspeaker). Power Amplifier Must Be Capable Of Handling Large Voltage Or Current Swings (Vmax To Vmin). The Main Aim Is To Develop Large Power Hence Called Powr Amplifier Stage Or Large Signal Amplifier.

Power Amplifiers Are Used in:

Power Amplifiers Are Used In Public Address Systems, Radio Transmitters, Servomotors , Tv Sets Etc.

Related Post:

What Is Sine Wave And Cos Wave ? Without Axis Is Sine

 AndCos Same ? 😉😉


Relationship Between Wavelength And Frequency And Energy


Trigonometry Table Trick


Bits And Byes

`
What Is Op-Amp?


What Is Verilog ?


Verilog Software 


What Is Log Or Logarithms ?


Verilog Project


Click Label To Check various Topics like Diodes,Rectifier,etc.

Contact tamilblogelectronic@gmail.com For Soft copies of any Book. 

I Try Contact back Immediately ( Max. 24 Hrs)

Telegram Link: https://t.me/tamilblog_electronics

Instagram Link: https://www.instagram.com/tamilblog_electronic/



Comments

Post a Comment

Welcome

Popular Post

boost::filesystem::remove: The process cannot access the file because it is being used by another process in VIVADO (XILINUX)

Image
( Note :   Click Label To Check various Topics like Diodes,Rectifier,etc.) Contact   tamilblogelectronic@gmail.com And other social media for Soft copies of any Book.   Final Year Engineering Project ( both Hardware and Software Project) :   Density Based Traffic control for Smart Ambulance System using Image Processing    Click Here   - Electronics Project Ambulance Detection Project In Vivado If You Run A Program With Both Main Module And Test Bench And You Try To Run Other Program In the Same Project Will You Will Get This Error  boost::filesystem::remove: The process cannot access the file because it is being used by another process in VIVADO If You Try To Run A Different Code In Same Project (I.e First You Tried Is Full Adder Second You Try To Run A Half Adder Or Any Thing With Correct Code(I.e Without Error In That Code) ) You May Get An Error As  boost::filesystem::remove: The process cannot access the file because it is being ...
Click To Read

Verilog Project

Image
( Note :   Click Label To Check various Topics like Diodes,Rectifier,etc.) Contact   tamilblogelectronic@gmail.com  And other social media for Soft copies of any Book. Traffic Light at Junction Let Us Go To The Logic Of The Project:  Logic Is More Important Than Code. Four Roads So Four Traffic Light: 1st traffic light is n_lights ( north direction light) 2nd  traffic light is e_lights   ( east direction light) 3rd  traffic light is s_lights   ( south direction light) 4th  traffic light is w_lights  ( west direction light) For n_lights: conditions: I am going 3bit  if 001 - GREEN     010 - YELLOW    100 - RED  For e_lights: conditions: I am going 3bit  if 001 -  GREEN     010 -  YELLOW    100 -  RED  For s_lights: if 001 -  GREEN     010 -  YELLOW    100 -  RED  For w_lights: if 001...
Click To Read

HOW TO CREATE PROJECT IN VIVADO (XILINUX) AND TEST BENCH

Image
      ( Note :   Click Label To Check various Topics like Diodes,Rectifier,etc.) Contact   tamilblogelectronic@gmail.com  And other social media for Soft copies of any Book.   AFTER INSTALL XILINUX  STEP 1 :CLICK ICON TO OPEN STEP 2: AFTER ITS OPENED THE SCREEN WILL BE LIKE THIS  STEP 3 : CLICK CREATE PROJECT AFTER YOU CLICKED CREATE PROJECT WILL BE LIKE THIS BELOW IMAGE: AFTER CREATE PROJECT CLICK NEXT THIS TAB WILL SHOW CLICK PROJECT NAME AND NAME THE PROJECT AND CLICK NEXT AFTER CLICK NEXT THIS TAB WILL SHOW CHOOSE RTL PROJECT AND CLICK NEXT CLICK CREATE FILE TO ADD SOURCE NAME AND TYPE SOURCE NAME AS LIKE GATE MODELLING MEANS    (gate_dff )  dff means d flipflop AFTER NAMED SOURCE WILL BE LIKE THIS CLICK NEXT CLICK NEXT THIS IS VERY IMPORTANT  CATEGORY : GENERAL PURPOSE PACKAGE : fb 484 SPEED : -1 FAMILY : KINTEX 7 AFTER YOU DID PREVIOUS STEPS ONLY TWO ROW WILL  BE THERE IN BOTTOM BOX.   CLICK ANY ...
Click To Read

fir filter advantages and disadvantages

 What is FIR Filters? The filters designed by using finite number of samples of impulse response are called FIR filters. These finite number of samples are obtained from the infinite duration desired impulse response h (n). Here h (n) is the inverse fourier transform of H (O), where H (0) is the ideal (desired) frequency response. The various methods of designing FIR filters It differs only in the method of determining the samples of h(n) from the samples of h (n). The various steps in designing FIR filter are i) Choose an ideal (desired) frequency response, H.(w). ii) Take inverse fourier transform of H (w) to get h,(n) or sample H, (o) at finitenumber of points (N-point) to get Ĥ(k). iii) If h (n) is determined, then convert the infinite duration h (n) to a finite duration h(n). (usually h(n) is an N-point sequence) or If ħ(k)is determined then take Npoint inverse DFT to get h(n). iv) Take Z-transform of h(n) to get H(z), where H(z) is the transfer function of the digital filter...
Click To Read